Deck Clips

NewTech Deck Clips

NewTech Deck Clips & Screws are available in tubs are supplied with 250 black plastic "T" clips fitted with a black finish stainless steel screw inserted and ready for fixing to timber joists or to steel joists. A driver is also supplied as part of the pack. Contact Futurewood if fixing to steel (joist).
 
decking shadow 2 1
decking shadow 2 2
Clip - Deck Clip-5

Futurewood Standard Deck Clips

Standard deck clips are designed to slide in to the grooved edge of the Futurewood board and be positioned over each joist. Once in position and after the boards have been checked for square on your deck and levered in to their final position the clip is screwed in to the joist providing a uniform 5.5mm gap between each board and a completely concealed fixing option.

Futurewood Standard Deck Clips & Screws are available with either screws for fixing to timber joists or metal joists.

FWPACK250 The NEWTECH deck clips are supplied in a box with 250 standard black polypropylene “T” clips fitted with blackened 316 stainless steel screws for fixing in to timber or aluminum joists. 3 Torx 15 drivers are also supplied in the deck clips box.

Boxes of 250 clips will cover 16sqm of 138mm wide decking boards installed on joists placed at 450mm intervals.

Anti-Walking Clips

The deck clip/anti-walking clip is both used to control the small amount of expansion & contraction produced by each board.

FWAWC50 Anti-Walking clips are supplied in packets of 50 c/w blackened stainless steel screws.

One anti-walking clip should be used per decking board regardless of the length of the board and the anti-walking clip should be used in place of the standard deck clip over the joist that is closest to the centre of the board.

Refer to the fixing guidelines to confirm the fixing method when using anti-walking clips on metal joists.


 
Clip - Anti-walking Clip-232
Clip - Start

Futurewood Starting/Finishing Clips

FWSTARCLIP Futurewood Starting/Finishing Clips are made from 304 stainless steel and supplied with 304 stainless steel screws for fixing to timber joists. These clips are supplied individually.

The starting/finishing clip is used on the outside edge of both the first or starting board and the last or finishing board as there is only 1 grooved edge of the decking board to work with and not enough joist to be able to use a standard deck clip.

One clip should be used every 900mm or every 2nd joist. If you are fixing to metal joists we recommend using a pop rivet to fix the clip. If the finishing board has been cut down to fit in a defined space and the outer groove is removed then we recommend using a router or biscuit cutter to cut a groove in the board edge every 900mm in order to fit the starting/finishing clips.

Futurewood Breaker Board Deck Clips

FWBBFIX Futurewood Breaker Board Clips consist of a black polyethylene clip with a nose and are supplied with 316 stainless steel screws for fixing to timber joists fitted to them. The pack size is 20 clips/screws and 1 Torx driver.

The breaker board clip is required when a breaker board or breaker boards make up part of the deck design. The breaker board clip is used in place of the standard deck clip between the end of the regular decking board and the side of the breaker board at approximately 900mm intervals (every 6, 138mm wide boards) to secure breaker boards to the joists.

Breaker board clips do not come with screws for metal joists refer to the fixing guidelines to confirm the fixing method when using breaker board clips on metal joists.


 
Clip - Breakerboard Clip with Hex Drill Bit-597

For more information see our fixing guidelines

 
The deck clip option is both economical to buy and saves installation time over a standard top fix screwing installation method.
 
Futurewood can also be fixed using an appropriate stainless steel screw fixed through the face of the board if required in certain area of the deck.
NEWSLETTER SIGN UP

Sign up for updates, news and more!

Email*
   
CONTACT US
 
FOLLOW US
  • EBOSS-logo-yellownew
1515new
ipsnew